As you move the cursor away from the end point once again, you will find a second line is shown, and is automatically attached to the endpoint of the previous line. When you are satisfied with the length of the line, left-click and release to place the endpoint. ![]() The length of the line can still be modified until it is constrained, either by additional sketch relations or dimensions. Note: The number that appears next to the endpoint of the line represents the length of the line, but does not act as a constraint. Showing Automatic Horizontal Sketch Relation These relations can be modified after the sketch has been created, and any that are not captured automatically can always be added. ![]() The yellow symbols are very important, as they represent sketch relations that will automatically be added as you create the sketch entities that is, if the line is created with the horizontal symbol present, that line will be locked in the horizontal orientation from that point forward (although the length may still be adjusted). As you approach a horizontal or vertical orientation, you will notice the line snap into place, and a yellow symbol will appear. In doing this, you are creating a Coincident sketch relation between the beginning of the line and the origin, effectively locking it in place.Īs you drag the cursor away from the origin, you will see a preview of the line. Left-click the origin and release to place the first point of the line on it. It is important to make use of the origin, especially in your first sketch, in order to fully define the sketch. Click the Line command to begin sketching. For new users, the Line command is the most basic sketch entity. On the left-hand side of the Sketch tab of the command manager, you will find several sketching tools that will allow you to construct a variety of basic shapes, including lines, circles and rectangles, among many others. First, you will notice that the Sketch icon we just used has now been replaced with an Exit Sketch icon.Īdditionally, you will find that the origin, originally blue in color, is now red.įinally, in the top right corner of the graphics area, you will see two icons that allow you to save the sketch (blue sketch icon) or cancel any changes (red X icon) and exit the sketch.Īt this point, we are ready to begin sketching. There are several indicators that sketch mode is active. For this reason, it is important for new users to be certain that sketch mode is active when creating dimensions. However, dimensions created outside of sketch mode will not constrain the sketch, and can become very confusing. Note: Dimensions are one important exception to this rule, as they can be added both within and outside of sketch mode. Likewise, many commands can be executed only when in sketch mode. It is important to understand when sketch mode is active, as many other SOLIDWORKS commands will be unavailable in this mode. Once a plane has been selected, the view orientation will automatically rotate normal to the plane, and you will be entered into sketch mode. To proceed, select one of the planes in the graphics area:ĭefault Planes Showing after Starting First Sketch Once the first sketch has been created, subsequent sketches will not automatically show these planes, although they can still be used.Īdditionally, any planar or flat faces of existing geometry can be used as sketching surfaces. Note: Be sure to select the Sketch icon and not the arrow beneath it – clicking the arrow will provide an option to create a 3D sketch, which we are not using here.īecause this is the first sketch in the new part, the system automatically displays the three default planes in the model, which act as the primary sketching surfaces in the model. Click the down arrow next to the search bar at the top right of the screen, choose Commands, and then type in the name of the command you'd like to use. Remember: You can search for commands in SOLIDWORKS if you do not know where they are. Once the user interface is visible, click the Sketch tab of the CommandManager and select the Sketch icon on the left-hand side. ![]() To begin, create a new part and select your desired template. Getting Setup for SketchingĪ sketch is almost always the first step in designing a new part. Sketches in SOLIDWORKS are like the foundation of a skyscraper – without them, you couldn’t build one! Well-developed sketches are one of the major keys to creating intelligent and flexible models, and we want to introduce you to several sketching tools/techniques and provide you with the understanding you need to start creating your own.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |